Canadian Manufacturing

Anaerobic adhesives improve the reliability of threaded fasteners

Prevent equipment failure and downtime from accidental loosening

Print this page

Threaded fasteners set and hold tolerances on assemblies ranging from light duty equipment to heavy machinery. Loosening is one of the major causes of industrial equipment failure, and results in millions of dollars of unscheduled downtime costs each year.

In many cases, fasteners that self-loosen during equipment operation may contribute to wear and fatigue, and result in poor operating tolerances, misalignment, and sometimes catastrophic equipment failure. Various types of differential stresses such as vibration and shock, thermal expansion and contraction, and micro-movement reduce clamping force on the assembly and ultimately cause machine failure.

Proactive maintenance of threaded fasteners has helped to increase equipment up-time. Maintenance activities that counteract self-loosening come in two basic categories—mechanical locking devices and chemical machinery adhesives.

Mechanical devices such as spring washers, wire retainers and locking bolts are costly and can’t reliably prevent self-loosening caused by side sliding motion. They don’t seal or prevent corrosion within the fastener assembly and must be sized appropriately for the specific fastener, resulting in large and costly parts inventories. Many mechanical locking methods loosen over time even under small vibrations.

Liquid threadlocking adhesives and sealants have become one of the most reliable and inexpensive ways to ensure that a threaded assembly will remain locked and leak proof for its entire service life.

Applied drop-wise to fastener threads, liquid anaerobic products fill the grooves of the threads and cure to a hard thermoset plastic when exposed to active metal ions in the absence of air. Machinery adhesives lock the threaded parts together, ensuring mating parts ultimately act as one conjoined part that resists failure and delivers the greatest possible reliability.

Most assemblies held together by threaded fasteners will at some time be dismantled for repairs, maintenance or adjustment. For this purpose, threadlockers are available in low strength formulations for easy removal, medium strength grades that can be removed using common hand tools, and high strength or “permanent” grades suitable for very demanding assemblies with minimal service requirements.

Even the highest strength threadlockers can be removed with standard hand tools following direct exposure to 450-500°F temperatures for about five minutes. The strength and viscosity of the threadlocker needed for an application are directly related to the size of the fastener used. Low-strength threadlockers are used on screws up to ¼ inch in diameter, such as adjustment and calibration screws, meters, gauges, and other fasteners that will need ongoing adjustment. Medium strength materials are for fasteners up to ¾ inch in diameter used in machine tools and presses, pumps, compressors, and as mounting bolts.

High strength threadlockers are best used on fasteners up to one inch in diameter found in permanent assembly applications such as heavy equipment and a variety of mounts. Low viscosity penetrating threadlocking formulations are also available that easily wick into pre-assembled fasteners up to ½ inch in diameter.Threadlocker image

Threadlocking adhesives should be applied only where the nut and bolt will meet when the assembly is fully tightened, as only adhesive between the threads will cure. For blind hole assemblies such as studs, threadlockers should be applied to the bolt and onto the threads within the blind hole. If adhesive is applied only to the bolt, air pressure may force the liquid to escape as the bolt is torqued down, and result in incomplete cure and possible assembly failure.

The operating conditions of the end use environment dictate the threadlocking formulation selected. The newest threadlocking technologies offer many advantages formerly unavailable, including surface insensitive, high temperature, and chemically resistant materials, as well as formulations engineered to withstand extreme vibration.

Recent advances in the stability and reactivity of threadlocking materials have allowed the development of semisolid “stick” formulations that complement their liquid counterparts. Semisolid threadlocking products work well in overhead or hard to see applications where liquids might be too messy or potential migration might be a problem.

The right threadlocking product can reduce costly downtime and equipment failure, providing maximum reliability on the shop floor.

Andy Barton is a senior application engineer, Henkel Corporation. To view more articles on adhesives and Henkel Corporation visit the Productivity Success Centre

If you would like to request a Loctite In-Plant Training work-shop click here.

Print this page

Related Posts from the network